Micro Control MCS-BMS-GATEWAY Průvodce řešením problémů Strana 156
- Strana / 162
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
MAGNUM VERSION 8 MANUAL REVISION 3.1
156
# Name Description
161 DEF TERM TMP
(Only HVAC)
If both coil #1 and coil #2 temperature are greater than the value of this Setpoint, then the
defrost cycle can be terminated.
B-PUMP FLT
(Boiler/Pump Control)
The ‘Value’ is not used as this set point is set up to check the status of a digital input indicated
in the Starting Pump Fault cell.
‘Time(sec)’ field: contains the delay before the system will place a pump in a failed state.
162 DEF TERM DEL
(Only HVAC)
The length of time in minutes of the defrost cycle.
163
HP HEAT TARG
(Only HVAC)
If active, then this value will become the target temperature during heating mode.
Purge Target
(Only CENT)
If active, it indicates that a Trane external purge system is incorporated. When the suction
temperature is less than this value for the number of seconds in the ‘Safety Down Time’,
then the purging sequence will begin.
B-HEAT TRGT
(Boiler/Pump Control)
The heating target that is to be maintained.
164
HP CTL ZONE +
(Only HVAC)
Added to Setpoint #163 “HP HEAT TARG” to create the upper limit of the control zone during
heating mode.
Purge Fault
(Only CENT)
If active and a purge safety switch is used, this Setpoint will contain the number of seconds
the switch must be ON before a purge error alarm occurs.
B-HEAT ZONE+
(Boiler/Pump Control)
The high dead band for the heating control zone. This value is added to the value of set point
#163.
165
HP CTL ZONE –
(Only HVAC)
Subtracted from Setpoint #163 “HP HEAT TARG” to create the lower limit of the control zone
during heating mode.
Purge ExTime
(Only CENT)
If the time in purging mode for the last 24 hours is greater than the value of this Setpoint, an
excessive purging alarm will be generated.
B-HEAT ZONE-
(Boiler/Pump Control)
The low dead band for the heating control zone. This value is subtracted form the value of set
point #163.
166 PHASE LOSS If active and the phase loss digital input is ON for the specified period of time, a safety trip
occurs. The system will attempt to restart after waiting the number of minutes contained
in the ‘Safety Down Time’ field of this Setpoint.
167 PURGE FLT ERROR If active and purge float error occurs, a purge float alarm is generated. This Fault requires a
lockout reset to resume purge operation.
168 PURGE COUNT If the total number of purges that occurred during the last three purge cycles exceed this
value, then reset all counters and generate a Maximum Purges Exceeded alarm. For the
first thirty minutes of compressor run time – this alarm is by passed.
169 PURGE PSI ST When the purge pressure sensor reading is equal or greater than this value, then a purge
cycle will be initiated. The cycle will end when the purge pressure sensor reading is less
than the value of this Setpoint minus Setpoint #193 “PSI DIFF”, or 5 psi if inactive.
170 EXCESS PURGE If the time in a purge cycle exceeds this Setpoint’s value in seconds, then the cycle will be
terminated and an Excessive Purge Time alarm will be generated. This fault requires a
lockout reset to resume purge operation.
171 FLA COMP#1 Full Load Amps for compressor #1. This is the amps at design suction and discharge
pressures referenced in the MCS-Config RO screen. This value is used to calculate the
high and the low amperage safety limits. Refer to Setpoints #75 and #76.
For screw compressors: The amp draw when the compressor is fully loaded. This value is
used to calculate the Full Load Amps Percentage (FLA %), which is used to control
loading and unloading the slide valve.
172 FLA COMP#2 Full Load Amps for compressor #2. Refer to Setpoint #171.
173 FLA COMP#3 Full Load Amps for compressor #3. Refer to Setpoint #171.
174 FLA COMP#4 Full Load Amps for compressor #4. Refer to Setpoint #171.
175 FLA COMP#5 Full Load Amps for compressor #5. Refer to Setpoint #171.
176 FLA COMP#6 Full Load Amps for compressor #6. Refer to Setpoint #171.
177 FLA COMP#7 Full Load Amps for compressor #7. Refer to Setpoint #171.
178 FLA COMP#8 Full Load Amps for compressor #8. Refer to Setpoint #171.
179 FLA COMP#9 Full Load Amps for compressor #9. Refer to Setpoint #171.
- HVAC and CENT V8 Software 1
- The DB Commitment: 2
- 1. Table of Contents 2
- OMPRESSOR 3
- 2. Revision Page 8
- 3.6. MCS Ethernet Port 11
- 3.3. About this Manual 11
- 3.4. About the Magnum 11
- 3.5. MCS 485 Network 11
- 4. Magnum Display Summary 15
- 5. Authorization Function 21
- 6. Magnum Control States 22
- 7. Standard Control Options 32
- 7.5. Compressor Types 34
- General Information 35
- Circuit Base setup 36
- Typical Relay Output Setup 38
- 7.10. Custom Rotation 43
- 7.15. Hot Gas Bypass 45
- 7.16. Chilled Water Reset 45
- 7.19. Oil Cooler Option 46
- 7.22. On/Off Switches 46
- 7.36. Operating Schedules 51
- Output Control 53
- Temperature) 58
- EXV Related Setpoints 63
- EXV Control States 63
- Tandem EXV Setup 64
- OUT48.1F 70
- IN45.3F 70
- KW Sensors 71
- Tonnage Sensors 71
- Configuring KW and Tonnage 72
- PG 74
- 7.75. Boiler/Pump Control 87
- Pump States 92
- Boiler States 92
- MCS-Config Setup 94
- CLLC States 97
- CLLC Valve States 97
- CLLC Control Logic 99
- 7.81. User Logic 105
- Operators 106
- User Sensor Input 107
- User Relay Output 108
- User Analog Output 109
- System Generated Alarms 111
- User Initiated Alarms 111
- 8.2. Magnum System Alarms 112
- 8.3. Setpoint safety alarms 112
- 9.1. Magnum Keypad Display 117
- 9.3. MCS-SI16-AO4 119
- 9.4. MCS-RO10 120
- 11.1. Sensor Input Points 123
- 11.2. Relay Output Points 124
- 11.3. Analog Output Points 124
- 11.4. Setpoints 125
- 11.6. Other Points 126
- Johnson N2 133
- 11.11.4 133
- 12. Relay Output Sequences 134
- Staging sequence 138
- 13. Magnum V8 Setpoints 140
- ALARM 141
- Low suction pressure 151
- High discharge pressure 151
- High amperage 151
- Discharge temperature 157
- Low oil seal temperature 157
- Low/high ambient cutoffs 157
- However, the EXV will 159
- EXVLevelTarget 161
Související produkty a manuály pro Brány / ovladače Micro Control MCS-BMS-GATEWAY
Chemtronics Electro-Wash CZ ES7101 Handbücher
Bedienungsanleitungen und Benutzerhandbücher für Für Zuhause Chemtronics Electro-Wash CZ ES7101.
Wir stellen 4 PDF-Handbücher Chemtronics Electro-Wash CZ ES7101 zum kostenlosen herunterladen nach Dokumenttypen zur Verfügung Bedienungsanleitung
Chemtronics Electro-Wash CZ ES7101 Bedienungsanleitung (2 Seiten)
Marke: Chemtronics | Kategorie: For Home | Größe: 0.04 MB |
Inhaltsverzeichnis
Chemtronics Electro-Wash CZ ES7101 Bedienungsanleitung (11 Seiten)
Marke: Chemtronics | Kategorie: For Home | Größe: 0.12 MB |
Inhaltsverzeichnis
Chemtronics Electro-Wash CZ ES7101 Bedienungsanleitung (10 Seiten)
Marke: Chemtronics | Kategorie: For Home | Größe: 0.12 MB |
Chemtronics Electro-Wash CZ ES7101 Bedienungsanleitung (10 Seiten)
Marke: Chemtronics | Kategorie: For Home | Größe: 0.12 MB |
Inhaltsverzeichnis
Weitere Produkte und Handbücher für Für Zuhause Chemtronics
| Modelle | Dokumententyp |
|---|---|
| Electro-Wash MX ES1621 |
Bedienungsanleitung
Chemtronics Electro-Wash MX ES1621 User Manual,
2 Seiten
|
| Electro-Wash MX ES1621 |
Bedienungsanleitung
Chemtronics Electro-Wash MX ES1621 Manuel d'utilisation,
12 Seiten
|
| Electro-Wash MX ES1621 |
Bedienungsanleitung
Chemtronics Electro-Wash MX ES1621 Manual del usuario,
11 Seiten
|
| Electro-Wash MX ES1621 |
Bedienungsanleitung
Chemtronics Electro-Wash MX ES1621 User Manual,
11 Seiten
|
| Electro-Wash MX Pen FW2150BLK |
Bedienungsanleitung
Chemtronics Electro-Wash MX Pen FW2150BLK User Manual,
2 Seiten
|
| Electro-Wash MX Pen FW2150BLK |
Bedienungsanleitung
Chemtronics Electro-Wash MX Pen FW2150BLK Manuel d'utilisation,
12 Seiten
|
| Electro-Wash MX Pen FW2150BLK |
Bedienungsanleitung
Chemtronics Electro-Wash MX Pen FW2150BLK Manual del usuario,
11 Seiten
|
| Electro-Wash MX Pen FW2150BLK |
Bedienungsanleitung
Chemtronics Electro-Wash MX Pen FW2150BLK User Manual,
11 Seiten
|
| Electro-Wash MX Presaturated Wipe CP421 |
Bedienungsanleitung
Chemtronics Electro-Wash MX Presaturated Wipe CP421 User Manual,
2 Seiten
|
| Electro-Wash MX Presaturated Wipe CP421 |
Bedienungsanleitung
Chemtronics Electro-Wash MX Presaturated Wipe CP421 Manuel d'utilisation,
12 Seiten
|
| Electro-Wash MX Presaturated Wipe CP421 |
Bedienungsanleitung
Chemtronics Electro-Wash MX Presaturated Wipe CP421 Manual del usuario,
11 Seiten
|
| Electro-Wash MX Presaturated Wipe CP421 |
Bedienungsanleitung
Chemtronics Electro-Wash MX Presaturated Wipe CP421 User Manual,
11 Seiten
|
| Electro-Wash NR ES1614 |
Bedienungsanleitung
Chemtronics Electro-Wash NR ES1614 User Manual,
2 Seiten
|
| Electro-Wash NR ES5514 |
Bedienungsanleitung
Chemtronics Electro-Wash NR ES5514 Manuel d'utilisation,
11 Seiten
|
| Electro-Wash NR ES5514 |
Bedienungsanleitung
Chemtronics Electro-Wash NR ES5514 Manual del usuario,
10 Seiten
|
| Electro-Wash NR ES5514 |
Bedienungsanleitung
Chemtronics Electro-Wash NR ES5514 User Manual,
10 Seiten
|
| Electro-Wash NR ES1614 |
Bedienungsanleitung
Chemtronics Electro-Wash NR ES1614 Manuel d'utilisation,
11 Seiten
|
| Electro-Wash NR ES1614 |
Bedienungsanleitung
Chemtronics Electro-Wash NR ES1614 Manual del usuario,
10 Seiten
|
| Electro-Wash NR ES1614 |
Bedienungsanleitung
Chemtronics Electro-Wash NR ES1614 User Manual [en] ,
10 Seiten
|
| Electro-Wash NX ES1611 |
Bedienungsanleitung
Chemtronics Electro-Wash NX ES1611 User Manual,
2 Seiten
|
© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.020 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce